Fume Hoods for Use With Remote Blower
|
All models feature:
- By-pass airflow design.
- **Ergonomic air foil with aerodynamic Clean-Sweep* airflow openings.
- Glacier white, dry powder epoxy-coated steel exterior.
- One-piece molded fiberglass liner and pre-set baffle(s) with flame spread less than 25 per ASTM E-84.
- **3/16" thick tempered safety glass vertical-rising sash(es) with epoxy-coated sash handle. Sash does not extend above the hood when fully open.
- **Removable front and side panels and front access panels for access to plumbing and electrical wiring.
- Pre-wired T8 fluorescent lighting, light and blower switches.
- **Molded fiberglass 12.81" ID exhaust connection(s).
Optional accessories for on-site installation include:
- Service Fixture Kits.
- Electrical Duplex Kits.
- Guardian Jr. and Digital Airflow Monitor Kits.
- Ceiling Enclosure and Rear Finish Panel Kits.
- Distillation Grid Kits.
- Auxiliary-Air Kits.
- Sash Stop Kits.
- Snuffer Fire Extinguishers.
All models require (not included):
- Remote Blower.
- Ductwork.
- Work Surface.
- Base Cabinet or Stand.
|
All models conform to the following regulations and standards:
- SEFA 1-2005
- NFPA45-2004
- ASTM E84-01
- ASHRAE110-95
- ANSI Z9.5-2003
- UL 3101-1/61010-1
- CAN/CSA C22.2 No. 1010.1
- UL 1805
- CE Conformity Marking (230 volt models)†
|
Fixtured models feature:
- Two pre-plumbed service fixtures with forged brass valves, lower right side with brass tubing for gas and lower left side with copper tubing for cold water. Components for converting either or both fixtures to air and vacuum are provided. Inlet tubing is not provided.
- One pre-wired 115 volt, 20 amp electrical duplex receptacle on lower right side (115 volt models)
|
With Sash Full Open (28") |
Nominal
Width |
Total Exhaust CFM and Static Pressure |
|
|
4 Feet
5 Feet
6 Feet
8 Feet |
730
960
1180
1660 |
.17"
.24"
.31"
.22" |
|
590
770
940
1330 |
.11"
.16"
.20"
.15" |
|
|
|
With Sash 60% Open (18")†† |
Nominal
Width |
Total Exhaust CFM and Static Pressure |
|
|
|
4 Feet
5 Feet
6 Feet
8 Feet |
470
610
750
1060 |
.07"
.11"
.14"
.08" |
|
380
490
600
850 |
.05"
.08"
.09"
.06" |
|
280
370
450
640 |
.03"
.04"
.05"
.03" |
|
|
|
|
| |
 |
* U.S. Patent No. 6,461,233
** Exclusive Feature
† pending
††Sash stop required
Heights of switches, electrical receptacle and service fixtures meet requirements of ADA. |
|
|
Ordering Information
Laboratory Hoods for use with remote blower
|
|
|
|
| 12.81" ID Exhaust Collar(s) |
|
|
|
|
|
|
|
| 4880100 |
| 4880400 |
| 4871500* |
| 4871600* |
|
| 115 volts, 60 Hz |
| 115 volts, 60 Hz |
| 230 volts, 50 Hz |
| 230 volts, 50 Hz |
|
|
|
| 2 ea. 25 watt |
| 2 ea. 25 watt |
| 2 ea. 25 watt |
| 2 ea. 25 watt |
|
|
|
| 325/147 |
| 335/152 |
| 325/147 |
| 335/152 |
|
|
| 6080100 |
| 6080400 |
| 6071500* |
| 6071600* |
|
| 115 volts, 60 Hz |
| 115 volts, 60 Hz |
| 230 volts, 50 Hz |
| 230 volts, 50 Hz |
|
|
|
| 2 ea. 32 watt |
| 2 ea. 32 watt |
| 2 ea. 32 watt |
| 2 ea. 32 watt |
|
|
|
| 410/186 |
| 420/191 |
| 410/186 |
| 420/191 |
|
|
| 7280100 |
| 7280400 |
| 7271500* |
| 7271600* |
|
| 115 volts, 60 Hz |
| 115 volts, 60 Hz |
| 230 volts, 50 Hz |
| 230 volts, 50 Hz |
|
|
|
| 2 ea. 32 watt |
| 2 ea. 32 watt |
| 2 ea. 32 watt |
| 2 ea. 32 watt |
|
|
|
| 485/220 |
| 495/225 |
| 485/220 |
| 495/225 |
|
|
|
| 115 volts, 60 Hz |
| 230 volts, 50 Hz |
|
|
|
| 4 ea. 25 watt |
| 4 ea. 25 watt |
|
|
|
|
| * International electrical configuration |
|
|
 |
 |
 |
 |
 |
 |
Dimensional Data
4',5',6' and 8' Laboratory Hoods for use with remote blower |
 |
4', 5' and 6' Hoods |
| |
A |
B |
C |
4' Hood
5' Hood
6' Hood |
48"
60"
72" |
38.25"
50.25"
62.25"
|
24"
30"
36" |
|
|
 |
 |
|
